AKCP locateWater Sensor (LWSC10)

Ideal for detecting waterleaks in hard to see areas, such as under raised floors and false ceilings. The locateWater sensor will give you a precise location of the water leak so you can respond promptly to protect your enterprise resources from water damage.

This sensor comes fully assembled and includes the rope portion that is the water sensing cable, the non-sensing cable (from the rope to the sensing module) and the main sensing module. The sensing cable can be pre-ordered from a 10 foot minimum to any custom run length (in multiples of 10 feet) of up to 160 feet. The non-sensing cable comes in a standard 20 foot run length.

The specific location of water along the rope can be used to trigger alerts like e-mail, SMS, phone calls and SNMP traps. The sensor has its own SNMP OID so that it can be monitored over the network using any Network Management System.

Each locateWater sensor comes complete with a 5 foot sensor cable that connects the main sensing module to the securityProbes RJ-45 sensor ports, or you can use your own CAT5/6 LAN cable. This cable can be extened up to 100 feet or 30 meters.

The AKCP locateWater Sensor is a rope type water sensor designed for specic location water detection.
The locateWater sensor can be connected to any one of the sensorProbe or securityProbe´s RJ-45 Intelligent Sensor ports enabling the unit to detect the specic location of water ingress.
This water sensor is a switch type that will be on or o and will detect the presence of water if a specic location on the rope becomes wet.

This is ideal when monitoring for water leaks under raised oor, or false ceiling areas.

This sensor comes fully assembled and includes the rope portion that is the water sensing cable, the non-sensing area cable (from the rope to the sensing module) and the main sensing module

The sensing cable can be pre-ordered from a 10 foot minimum to any custom run length (in multiples of 10 feet) of up to 160 feet. The non-sensing cable comes in a standard 20 foot run length. See the detailed diagram of the sensor assembly on page number 2 showing the cable.

The sensing module is then connected to any of the RJ-45 Intelligent sensor ports on the AKCP base units using standard CAT5/6 LAN cable.

The specic location of water along the rope can be used to trigger alerts like e-mail, SMS, phone calls and SNMP traps. The sensor has its own SNMP OID so that it can be monitored over the network using any Network Management System.

Each locateWater sensor comes complete with a 5 foot sensor cable that connects the main sensing module to the securityProbes RJ-45 sensor ports, or you can use your own CAT5/6 LAN cable. This cable can be extended up to 100 feet or 30 meters.

Note:
The locateWater Sensor is only compatible with the securityProbe, securityProbe 5E, securityProbe 5ES, newer sensorProbe2 shipped after October 2009, sensorProbe4, and sensorProbe8, sensorProbe8-X20/X60 units shipped after July 1st 2011.

Water
Ideal for use in basements and under false oors and roof spaces, the locateWater sensor can cover a large area. Combined with any of the sensorProbe series or securityProbe series units it will give you advance notice of any water leaks or ooding. The sensor will retain its error condition until it is read via an SNMP get. Therefore if the sensor encounters a critical condition at anytime it will report that condition before it returns to a normal state

Specifications

Measurement Range

• Wet or Dry (-20 degrees C- +60 degrees C)

Measurement Accuracy

• Able to detect the presence of water at a specific location

Sensor Type

• Patent pending, capacitance measurement technology

Power Consumption

• Typical 125 mWatt, 25 mA

Communications Cable

• RJ-45 jack to main sensor module using UTP CAT5 cable. Maximum extension cable length is 30 meters or 100 feet

Power Source

• Powered by the sensorProbe, or securityProbe. No additional power needed. Both units autodetects the presence of the ropeWater sensor
• Comes fully assembled and includes the rope portion that is the water sensing cable, the non-sensing area cable (from the rope to the sensing module) and the main sensing module
• Sensing rope cable can be pre-ordered from a 10 foot minimum to any custom run length (in multiples of 10 feet) of up to 160 feet
• Non-sensing cable comes in a standard 20 foot run length

Note

• AKCP does not recommend the locateWater Sensor to be placed on a conductive surface.

SNMP OID?s

SNMP OIDs for the sensorProbe units are as follows:
sensorProbeSwitchWaterRopeLeakLocation .1.3.6.1.4.1.3854.1.2.2.1.18.1.49.X
sensorProbeSwitchWaterRopeLength .1.3.6.1.4.1.3854.1.2.2.1.18.1.50.X
sensorProbeSwitchWaterRopeUnit .1.3.6.1.4.1.3854.1.2.2.1.18.1.51.X
sensorProbeSwitchWaterRopeOhmPerUnit .1.3.6.1.4.1.3854.1.2.2.1.18.1.52.X
sensorProbeSwitchWaterRopeRaw .1.3.6.1.4.1.3854.1.2.2.1.18.1.53.X
Where X is port-1

SNMP OIDs for the securityProbe units are as follows:
sensorWaterRopeDescription .1.3.6.1.4.1.3854.2.3.21.1.2.Y
sensorWaterRopeStatus .1.3.6.1.4.1.3854.2.3.21.1.6.Y
sensorWaterRopeGoOnline .1.3.6.1.4.1.3854.2.3.21.1.8.Y
sensorWaterRopeLeakLocation .1.3.6.1.4.1.3854.2.3.21.1.9.Y
sensorWaterRopeLength .1.3.6.1.4.1.3854.2.3.21.1.10.Y
sensorWaterRopeUnit .1.3.6.1.4.1.3854.2.3.21.1.11.Y
sensorWaterRopeRaw .1.3.6.1.4.1.3854.2.3.21.1.13.Y

where Y is sensor ID, the dynamically number is generated when the sensor plugged in.





Ordering Information

Product Model	Order Number	Descrition
Locate Rope Water Sensor
LWSC10	940099	10ft Locate Rope Water Sensor
LWSCCAB10		10ft extension cable for RWSC10 and LWSC10
LWSCCABXX	940180	Extension (1 metre)