AKCP Siren Strobe Light (STR00)
Audio and visual alarm notification
- Combined siren and strobe on a single Intelligent sensor port
- Powered by the base unit, no additional power source required
- Can be extended up to 30 m (100 ft.) from the base unit
- 100db Siren sound
- 400x per minute flashing strobe
The combined strobe light and siren can add eye-catching audio visual alarms to the sensorProbe and securityProbe series base units. When triggered, the siren generates a loud alarm accompanied with a bright flashing strobe light, giving a clear alert of an alarm condition.
Powered by the base unit, with no additional power required, it?s perfectly suited for use in mission critical situations. The siren and strobe can be triggered by another sensors status, or controlled manually via the web interface or using it?s own SNMP OID.
The siren and alarm are both incorporated into one device. Up to 2 siren and strobes can be connected to the intelligent sensor ports on the sensorProbe2 device.
On sensorProbe 8, securityProbe 5E and E-sensor8 expansion module. Each device comes with a free CAT5 cable, 5 feet in length.
You can connect the siren / strobe light using your own CAT 5 cable up to 100 feet, allowing the sensors to be positioned in hot spots.
When a combined siren / strobe light is plugged into the intelligent sensor port, the base unit will auto detect the sensor, and it display the status of the device. The siren / strobe light can be triggered manually, via the web interface, or it can be congured to turn on at certain times, through the web interface.
The device can be triggered by any sensor connected to a sensorProbe or securityProbe device, or by an alarm condition generated by the base unit. It can be fully integrated with the sensor notication matrix on the securityProbe series. Each device has its own SNMP OID so that status can be collected over the network, and additionally the siren and strobe can be controlled via SNMP across a network.
Powered by the base unit, with no additional power required, it?s perfectly suited for use in mission critical situations. The siren and strobe can be triggered by another sensors status, or controlled manually via the web interface or using it?s own SNMP OID.
The siren and alarm are both incorporated into one device. Up to 2 siren and strobes can be connected to the intelligent sensor ports on the sensorProbe2 device.
On sensorProbe 8, securityProbe 5E and E-sensor8 expansion module. Each device comes with a free CAT5 cable, 5 feet in length.
You can connect the siren / strobe light using your own CAT 5 cable up to 100 feet, allowing the sensors to be positioned in hot spots.
When a combined siren / strobe light is plugged into the intelligent sensor port, the base unit will auto detect the sensor, and it display the status of the device. The siren / strobe light can be triggered manually, via the web interface, or it can be congured to turn on at certain times, through the web interface.
The device can be triggered by any sensor connected to a sensorProbe or securityProbe device, or by an alarm condition generated by the base unit. It can be fully integrated with the sensor notication matrix on the securityProbe series. Each device has its own SNMP OID so that status can be collected over the network, and additionally the siren and strobe can be controlled via SNMP across a network.
SNMP Commands
The sensor can also be controlled manually using the following SNMP commands:
options:
Disabling the Siren/Strobe or controlling the volume
In normal operation both the siren and strobe light are activated as they are on the same circuit, however there are a couple of options for modifying the sensor to your requirements.
You can open the case of the sensor and physically remove the wire to the siren, or strobe light to deactivate one, or the other.
Alternatively , you can wire in a potentiometer, or a switch into the siren/strobe sensor. This would allow you to control the volume or disable the siren while leaving the strobe light active.
You can wire in-line, a 5 ohm potentiometer (pot), or a switch with the siren, then it would be possible to adjust volume,
or turn it on or off completely.
Specifications
Measurement Range
Communications Cable
Sensor Type
Power source
Power Consumption
Measurement Rate
Alarmsound
Strobe Flash Frequency
Light Source
Dimension :
72 x 123 x 45 mm
Ordering Information
The sensor can also be controlled manually using the following SNMP commands:
options:
- 1 = allow-sensor-control
- 8 = cycle-On-O-On
- 7 = cycle-O-On-O
- 3 = turn-on
- 4 = turn-off
Disabling the Siren/Strobe or controlling the volume
In normal operation both the siren and strobe light are activated as they are on the same circuit, however there are a couple of options for modifying the sensor to your requirements.
You can open the case of the sensor and physically remove the wire to the siren, or strobe light to deactivate one, or the other.
Alternatively , you can wire in a potentiometer, or a switch into the siren/strobe sensor. This would allow you to control the volume or disable the siren while leaving the strobe light active.
You can wire in-line, a 5 ohm potentiometer (pot), or a switch with the siren, then it would be possible to adjust volume,
or turn it on or off completely.
Specifications
Measurement Range
- Alarm or Normal
Communications Cable
- RJ45 jack to sensor using UTP Cat 5 wire
Sensor Type
- Open/closed contact switch
Power source
- Powered by the sensorProbe. No additional power needed
Power Consumption
- Typical 556.50 mWatt, 111.30mA
Measurement Rate
- Multiple readings every second
Alarmsound
- 100±3db@100cm
Strobe Flash Frequency
- ?400 Times/Minute
Light Source
- Super bright LEDs x8
- Maximum extension cable length 30m (100 ft.) with approved low capacitance shielded cable or UTP
- Up to 2 Siren Strobe sensors per sensorProbe2, 8 per sensorProbe8 and securityProbe
- Full autosense including disconnect alarm
Dimension :
72 x 123 x 45 mm
Ordering Information
Product Model | Order Number | Description |
---|---|---|
Siren & Strobe Light | ||
STR00 | 949021 | 5ft cable Siren & Strobe |
STR15 | 15ft cable Siren & Strobe | |
STR40 | 40ft cable Siren & Strobe | |
STR60 | 60ft cable Siren & Strobe | |
STR100 | 100ft cable Siren & Strobe | |
V-STRxx | Variable Siren Volume |
Kunden, die diesen Artikel gesehen haben, sahen auch