HW group WLD2
Quad water leak detector with WiFi and Ethernet
- Simple installation, support for automatic network configuration via DHCP.
- Intuitive WWW interface for fast and easy installation.
- Ability to communicate over WiFi (external antenna for extended range, support for 2.4GHz, 2.11 b/g/n) and Ethernet at the same time.
- With support for up to 4 sensing cables (each max. 85m), detection capabilities can be scaled and the source of the leak more easily identified.
- The sensing cable can be fixed using clips or adhesive tape.
- WLD2 signals the following states: OK / Flooded / Sensing cable fault.
- Flooding alerts can be send as a standard e-mail, or as a text message (SMS) through a SMS gateway available from HW group.
- Detected leaks or WLD sensing cable disconnections can be signaled by activating a relay output at a Poseidon2 or Damocles2 unit over the Ethernet.
- WLD2 can be easily mounted on a wall or in a 19" cabinet.
- Powered over PoE or from an external adapter.
WLD2 is a WiFi / Ethernet water leak detector with support for WWW, SNMP, e-mails and PoE. It uses up to 4 very sensitive sensing cables. Alarms are triggered by even the smallest volumes of liquids, such as condensation from A/C pipes or water leaks in general. You will receive alarms before costly damages occur. In addition to flooding, the device also detects disconnected or damaged sensing cables for increased reliability.
Thanks to WiFi connectivity, the WLD2 water leak detector can be installed in remote places. In case of flooding, it can send an alert via e-mail, SNMP trap, or the SensDesk cloud. With an external SMS gateway by HW group, it can send a text message or dial a phone number. Of course, in critical applications, it can also communicate via wired Ethernet and can be powered with PoE.
WLD2 supports zone creation. The flood sensor can call a different phone number for each zone.
WLD2 can be connected to the SensDesk portal using the HWg-Push protocol, as well as to standard monitoring systems thanks to SNMP and SNMP Trap support. Flooding can be also indicated by switching a remote output (e.g. a relay) over the network (Box-2-Box mode with a Poseidon2 or Damocles2 unit), independently for each sensing cable. Compared to HWg-WLD, up to 4 independent detecting cables can be connected to the WLD2 to help locate the leak more accurately.
Applications and usage:
- Water detection under raised floors.
- Leaky pipe detection (cable wrapped along the pipe).
- Protection against floods from skylights – sensing cable routed along the walls.
- Detection of water leaks in drip trays.
- Detection of water leaks under air-conditioning outlets.
SPECIFICATIONS
Ethernet | |
Interface | RJ45 (10/100BASE-T) |
Supported protocols | IP: ARP, TCP/IP (HTTP, HTTPS, SNTP, SMTP, HWg-Push, netGSM, TLS), UDP/IP (SNMP) |
SNMP | Version 1 fully supported, some parts version 2 |
WiFi | |
Supported standards | 802.11 b/g/n |
Frequency | 2,4 GHz |
Output | +19.5 dBm output power in 802.11b mode +16 dBm for 802.11n |
Security | WEP / WPA / WPA2 PSK / WPA2 TSK / WPS |
Antenna | Internal |
External sensors | |
Number/Connectors | WLD1, WLD2, WLD3, WLD4 / terminal blocks |
Type | Moisture sensing cable |
Connector | Terminal block |
Sensor states | 0 = OK, 1 = Flooded, 2 = Cable disconnected |
Sensing cable length | Max. 85 m |
Cable extension | May be extended by at most 100 m, AWG 24 |
Power supply | |
Power voltage | 5V / 250 mA |
Connector | Jack Ø 3.5 × 1.35 / 10 mm |
PoE (Power over Ethernet) | RJ45 - IEEE 802.3af Class 0 |
Other parameters | |
Operating temperature | -10 to 60 °C (range of device operating temperatures – may not correspond to sensor range) |
Dimensions/weight | 65 × 80 × 30 mm / 500 g |
Elmag. radiation | CE / FCC Part 15, Class B |
Elmag. compatibility | EN 55022, EN 55024, EN 61000 |
ORDERING INFORMATION
Available Modules / Accessories | |
WLD2 PoE | Water Leak Detector plain unit. 4 detection cable inputs / zones, PoE Support. Ethenet and WiFi connectivity |
WLD2 PoE SET | Water Leak Detector plain unit. 4 detection cable inputs / zones, PoE Support. Ethenet and WiFi connectivity Full package with 2m detection cable + 2m connection cable, power adaptor. |
Kunden, die diesen Artikel gesehen haben, sahen auch