AKCP In-Line Power Meter (ILPM)
Power Monitoring and Switching
- Monitor and switch an individual Appliance
- Monitor complete Power Strip, turn a power strip into a smart PDU
- Graph power, voltage, current parameters.
- Receive alerts if electrical parameters exceed your pre-defined thresholds
- Shutdown power automatically if over voltage, over current, or smoke detected
- Optional Thermal Map for use in a Rack+ system
- Optional Smoke Detector for Patent Pending Fire Suppression
- Optional LCD Display
- Bare end wires as standard or optional plug
- 100-250 AVAC Input
The power meter goes between the electrical source and the power strip, or individual appliance, monitoring the voltage (V), current (A) and Kilowat Hours (kWh) being consumed with billable grade accuracy. Remotely switch devices on and off with optional relay. Relays are Bi-Stable Latched relay, which retains it?s state regardless of whether it is receiving power or not.
Inline Power Meter is essential for:
- Checking how close you are to tripping your circuit breaker
- Ensure sufficient power overhead before adding new equipment to a circuit
- Billing individual clients in co-located services
- Monitoring up to 16 In-Line Power Meters from a single sensorProbe+
Advantages
Removing the controller from your power strip allows you to use a low cost basic power strip. This gives several advantages, in addition to the cost savings.
- A single IP address to monitor multiple cabinets.
- Hot swappable controller, no downtime to cabinets if servicing is needed
- More space for outlets on your power strip as the controller is moved out of the 0U space
- As future needs increase, just change the power strip no need for new controller and power meter.
ILPM - Technical Specification
Ordering Information
Measurements | |
Power Rating | Input Voltage rating : - 1 phase - 100V~250V AC Current Rating : - 16A - 32A |
Power Measurements | - Voltage (V) - Current (A) - Active Power (kW) - Total Active Energy (kWh) - Leakage current (A) - Power Factor |
Environment monitoring | Optional Cabinet Thermal Map (-CTM or -CTHM) - Temperature sensor *range -40°C to +75°C - Humidity sensor * 0 to 100% Relative humidity |
Control | |
Switching Relay | Latched Relay Contacts rating : 40 Amp Mechanical Life : 1 10^7 times Electrical Life : 3 10^4 times Class B |
Status Indication | LED indication for power LED Relay status (with optional relay) |
Inputs | 1x sensor RJ45 Port Hardwired with following plugs : - IEC 60320 C20 - IEC 60320 C14 - Nema 5-15P - Nema 5-20P - Nema 5-30P - Nema L5-15P - Nema L5-20P - Nema L5-30P - UK BS - Shuko CEE 7/7 plug - IEC60309 2P+E blue |
Outputs | Outlet types : - IEC 60320 C13 - IEC 60320 C19 - Nema 5-15R - Nema 5-20R - Nema 5-30R - Nema L5-15R - Nema L5-20R - Nema L5-30R - UK BS1363 - Shuko CEE 7/3 Socket - IEC 60309 2P+E Blue |
Interface | |
Communications cable | RJ-45 jack to sensor using UTP CAT5e/6 cable |
Power source | Powered by the sensorProbe+ familiy units. No additional power needed |
Power Consumption | Typical 800 mWatt, 160 mA Peak 1.75 Watt, 350 mA |
Maximum Cable Length | Run length is 32 feet (10 meters) with approved low capacitance shielded cable or UTP |
Dimensions | 170 x 85 x 52 mm |
Mounting | Keyhole mounting |
Components | Manufactured using highly integrated, low power surface mount technology to ensure long term reliability. |
Operating Environment | Temperature : Min. -35° C - Max.80° C Humidity: Min. 20% - Max. 80% (Non-Condensing) |
MTBF | 1,400,000 Hours based on field experience with sensorProbe units. |
Important Note | sensorProbe+ units auto detects the presence of the ILPM sensor - The ILPM sensor is only compatible with the sensorProbe+ platform units. - When plugging the first time or after upgrading a sensorProbe+ unit, the sensor's firmware might be upgraded by the unit and not be available right away. - On the sensorProbeX+, the sensor can be used only on the main module sensor ports |
Sensor count | ILPM : 5 ILPM-LR : 6 -CTM : +9 -CTHM : +11 |
Ordering Information
In-Line Power Meter | |
ILPM-32A | "Inline power Meter 32A 25cm power in / out cable with bare ends" |
ILPM-16A | "Inline power Meter 16A 25cm power in / out cable with bare ends" |
In-Line Power Meter Options | |
Relays | |
LR | Latched relay |
Thermal Maps | |
ILPM-CTM | Cabinet Thermal Map - Temperature only |
ILPM-CTHM | Cabinet Thermal Map - Temperature & Humidity |
10A Connections | |
C13 | IEC C13 (Power Out) |
C13L | IEC C13 Locking (Power Out) |
C14 | IEC C14 (Power In) |
13A Connections | |
UKP | UK Plug (Power In) |
15A Connections | |
AUS | AUS (Power In) |
5-15R | Nema 5-15R (Power Out) |
5-15P | Nema 5-15P (Power In) |
16A Connections | |
EURP | EUR (Power In) |
C19 | C19 (Power Out) |
C19L | C19 Locking (Power Out) |
C20 | C20 (Power In) |
2PEP | IEC 2P+E (Power In) |
2PEO | IEC 2P+E (Power Out) |
20A Connections | |
5-20R | Nema 5-20R (Power Out) |
L6-20P | Nema L6-20P (Power In) |
5-20P | Nema 5-20P (Power In) |
30A Connections | |
5-30P | Nema 5-30P (Power In) |
L6-30P | Nema L6-30P (Power In) |
32A Connections | |
2PEP-32 | IEC 2P+E (220V Power In) |
2PEO-32 | IEC 2P+E (220V Power Out) |
Kunden, die diesen Artikel gesehen haben, sahen auch